By Chris Perry, Quality Manager – Epec Engineered Technologies
When designing PCB’s in a multi-up array, most designers choose v-score as the singulation method over traditional rout and breakaway tabs. The benefits gained range from effortless removal of parts from panel form, to realized cost savings with better utilization of panel area. When designing a circuit board with v-score, there are two areas of concern - the angle of the cut, and the depth of the cut.
Referring to the angle of the cut, the wider the angle makes it easier for part removal. A narrow angle will leave a thinner channel, allowing the designer more flexibility with image placement. A 30° angle is standard, which leaves a .015” channel, but thicker materials such as .093” or higher, may be better suited for the wider 60° angle. The depth of v-score is measured by the remaining web thickness (groove center material left behind after v-score process). For standard laminates, at .062 thick, a .020” web thickness (+/-.004” tolerance) is recommended. For high temperature laminates, which tend to be brittle and fracture easily, a .015” web thickness (+/- .004” tolerance) is recommended for .062” thick laminates.
V-score does come with challenges. If the parts do not breakout easily, it can lead to fracturing of the circuit boards during singulation, and also part dimension issues. These issues can be caused by a poor singulation process, incorrect v-score specifications, or a quality shortfall at the actual v-score process.
Difficulty in breaking the parts from the v-scored array can be dependent on how the parts are removed from the array. In many cases manual hand separation is good enough to remove the assembled parts from the array. However, when the populated part leaves little room to sufficiently grasp the assembly, or the assembly uses a thicker laminate, a v-score cutter (pizza cutter) may be utilized. This cutter allows removal without unwarranted stress on the assembly itself.
When assemblies are difficult to remove, the forces placed on the assembly will cause what appears to be a haloing along the part edge. The haloing effect is a fracturing of the fiberglass bundles and resins of the base laminate. In a worst case scenario, the separation will happen outside of the v-score channel and cause uneven breaks along the board edge. Possible causes for this issue can be incorrect v-score depth specification for the laminate used or rough part removal, placing excess stresses on the part. Inconsistencies with the v-score itself can lead to this. A dull blade or blades can cause the cut to be more of a “U” shape as opposed to the correct “V” shape.
This will increase difficulty in breaking out and leave excess material after singulation. An offset v-score - which is when one cut is deeper on one side of the part, due to blade settings, will also cause uneven and difficult singulation.
Finally, we have seen some suppliers use a “milling” process or a controlled depth rout, as an attempt to replace actual v-score. When these parts are separated, there will be an excessive amount of material left over, that many CM’s and OEM’s will find problematic. This process is highly discouraged.
It is also important to note that with all v-score processes, there will be remaining laminate material on the part edge, after the parts are singulated.
Typically the remaining material is too minute to affect the part fit, but if the design calls for a very low tolerance with unit fit, there could be an issue. Remember that if a part is scored on opposite edges, the remaining material on both sides can add up to enough that will cause a fit challenge in the final unit.
Make sure to download our Free Technical Engineering & Design Guides which are packed with data from our high tech manufacturing capabilities.
When designing PCB’s in a multi-up array, most designers choose v-score as the singulation method over traditional rout and breakaway tabs. The benefits gained range from effortless removal of parts from panel form, to realized cost savings with better utilization of panel area. When designing a circuit board with v-score, there are two areas of concern - the angle of the cut, and the depth of the cut.
 |
| V-Scored PCB and a Cross Sectional View of a V-Score Cut. |
Referring to the angle of the cut, the wider the angle makes it easier for part removal. A narrow angle will leave a thinner channel, allowing the designer more flexibility with image placement. A 30° angle is standard, which leaves a .015” channel, but thicker materials such as .093” or higher, may be better suited for the wider 60° angle. The depth of v-score is measured by the remaining web thickness (groove center material left behind after v-score process). For standard laminates, at .062 thick, a .020” web thickness (+/-.004” tolerance) is recommended. For high temperature laminates, which tend to be brittle and fracture easily, a .015” web thickness (+/- .004” tolerance) is recommended for .062” thick laminates.
V-score does come with challenges. If the parts do not breakout easily, it can lead to fracturing of the circuit boards during singulation, and also part dimension issues. These issues can be caused by a poor singulation process, incorrect v-score specifications, or a quality shortfall at the actual v-score process.
Difficulty in breaking the parts from the v-scored array can be dependent on how the parts are removed from the array. In many cases manual hand separation is good enough to remove the assembled parts from the array. However, when the populated part leaves little room to sufficiently grasp the assembly, or the assembly uses a thicker laminate, a v-score cutter (pizza cutter) may be utilized. This cutter allows removal without unwarranted stress on the assembly itself.
When assemblies are difficult to remove, the forces placed on the assembly will cause what appears to be a haloing along the part edge. The haloing effect is a fracturing of the fiberglass bundles and resins of the base laminate. In a worst case scenario, the separation will happen outside of the v-score channel and cause uneven breaks along the board edge. Possible causes for this issue can be incorrect v-score depth specification for the laminate used or rough part removal, placing excess stresses on the part. Inconsistencies with the v-score itself can lead to this. A dull blade or blades can cause the cut to be more of a “U” shape as opposed to the correct “V” shape.
 |
| PCB V-Score Results with Dull Blade |
This will increase difficulty in breaking out and leave excess material after singulation. An offset v-score - which is when one cut is deeper on one side of the part, due to blade settings, will also cause uneven and difficult singulation.
 |
| Printed Circuit Board Offset V-Score |
Finally, we have seen some suppliers use a “milling” process or a controlled depth rout, as an attempt to replace actual v-score. When these parts are separated, there will be an excessive amount of material left over, that many CM’s and OEM’s will find problematic. This process is highly discouraged.
 |
| PCB Scored Edge with Mil Process |
It is also important to note that with all v-score processes, there will be remaining laminate material on the part edge, after the parts are singulated.
 |
| PCB Scored Board Edge After Seperation |
Typically the remaining material is too minute to affect the part fit, but if the design calls for a very low tolerance with unit fit, there could be an issue. Remember that if a part is scored on opposite edges, the remaining material on both sides can add up to enough that will cause a fit challenge in the final unit.
Make sure to download our Free Technical Engineering & Design Guides which are packed with data from our high tech manufacturing capabilities.